How to reset spectrum remote?

In this article we will discuss about how to reset spectrum remote. Spectrum remotes are quite popular in the electronic market. Spectrum remotes are the most common TV remote controllers available in the market. They are accessed via programmable keys that you can turn on multiple devices using a remote control and even a console.

Are you wondering how to fix Spectrum remote that is not working? Check that the remote control is in the correct mode: TV, DVD, AUX, or DVD by pressing the Select/OK button or by checking the Mode key. Unplug TV from power source, remove battery from remote, wait 1 minute, plug everything back in.


If you using Spectrum for internet and TV for some time. And they also faced some problems like Spectrum remote control not working as expected. The technology used in most home remote controls is Infrared Light (IR) and this makes the model you choose an exceptional one.

Unfortunately, your Spectrum remote control may not work as expected and may make it difficult to use your TV or any other device. If your Spectrum remote isn’t working, try replacing the battery, enable TV controls, remove signal interruptions, and factory reset your Spectrum remote. remote reset. In extreme cases, you may even have to replace it completely. What you can see below:

Some common spectrum remote control issues:

  • LED light is no longer flashing
  • The channels are not getting changed by the remote control or changing way too slowly
  • Red light flashing over and over again
  • Remotes are changing the channels but not the volume
  • Lagging response
  • Remote is not working complete

Reset it using factory defaults:

Factory reset it to default settings. If you programmed your Spectrum remote incorrectly to the extent that you are unable to use it properly, you can try this reset everything and you will have to set up your remote again.

  • Firstly, press and hold the TV button.
  • While holding it press the OK button for 1 second and then release both the buttons simultaneously. Here, all three (TV, DVD, AUX) buttons will flash and the TV button will remain lit.
  • Now you have to press and hold the Delete button for 3 seconds. Here, the TV button will remain off.
  • Now your TV remote will be reset to factory settings. Now you need to repair it with RF2IR converter:
  • Firstly, unplug the RF2IR Converter from the set top box.
  • Now press and hold Find to put the RF2IR converter back in the set top box
  • Now release Find This will delete the old pairing code.
  • You have to bring the remote close to a few feet of the set top box and press any key on the remote
  • Pair it with an RF2IR converter.
  • Once the pairing is successful, pressing the Find key on the RF2IR Converter will cause the remote to play sound and work as expected.

Causes of spectrum not working error:

Here are some causes of spectrum remote not working:

Physical damage – When your spectrum remote stopped working after smashing on the floor or hitting a hard object, it’s damaged and needs a replacement. Also, certain keys may not be functioning properly as a result of physical damage.
Changing Remote Battery – when the batteries become weak, the remote starts malfunctioning and finally, stops working. Dead batteries could cause the channel to change slowly.
Data on the remote is badly set up – a wrong spectrum remote set up result in several issues. The remote has different modes allowing the user to choose a device to control. Ensure you are on the correct setting for the device you want to operate.
Your spectrum cable box has issue – sometimes, your spectrum remote is not working with cable box as a result of problems with the cable box.
Pairing is not done correctly– Spectrum remotes are easy to program, and you may not have automated it correctly to work with the corresponding device or console.

Troubleshooting of Spectrum Remote Control:

There are some troubleshooting steps below:

  • If your battery is down then replace your batteries.
  • Make sure your Spectrum Receiver is turned on.
  • Change channels by pressing the buttons on your receiver.
  • Remove any objects around your receiver.
  • Position your receiver at a different angle so it can detect your remote.
  • If you have more than one receiver, make sure you’re using the correct remote for this receiver.
  • Reboot your receiver by unplugging it and plugging it back in.

I hope this guide is helpful to you.

Thank you!!